Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now


Review: Event Opal Studio Monitors

Gems From Down Under

Watch a video on the Opals

Opal’s curved enclosures have no parallel surfaces.

Named for the national gemstone of Australia, are Opals, the new studio monitors from Event Electronics. Despite their relatively compact 11.6×17.7×10.8-inch enclosures, Opals were intended to create a two-way system that delivers the power, accuracy and fidelity of large three-way systems.

This was no easy task. From day one, designer Marcelo Vercelli took a completely new look at the process, with the intent of creating a no-compromise monitor with world-class performance. There’s no off-the-shelf stuff here. All the components were built from the ground up, combining new and traditional technologies.

Discovering Opals
The 8-inch woofer has a neodymium motor and a low mass, composite long-strand carbon fiber/paper cone that’s stiff enough to provide midrange out to 10 kHz, yet delivers 35Hz bass with remarkable 30mm-plus excursion. The woofer’s dual X-Coil™ design combines an active and a parallel, second voice coil for improved transient response, even under extreme workouts.

The tweeter has a 1-inch beryllium/copper alloy dome mated to a neodymium magnet structure and mounted on an asymmetrical elliptical waveguide for dispersion control in the horizontal and vertical planes. The entire HF unit and illuminated Event logo are rotatable for using Opals on their sides.

A 1,600 Hz center-point, 8th-order (48dB/octave) active network handles crossover duties. The onboard bi-amplification provides 600 LF/140 HF watts of peak power via linear Class-AB amps. Looking inside, components are top-grade, while heavy toroidal transformers and massive rear-panel heat sinks contribute much to Opal’s 47-pound heft, so be wary of meter bridge placement. Full power THD specs for the amps are in the 0.004 percent range. Neutrik Combo XLR/TRS jacks handle balanced or unbalanced inputs; a 15-pin D-sub connector is provided for a planned digital input module.

Finished in black powercoat, the molded aluminum enclosures have no parallel surfaces, and all sides are radiused to minimize diffraction effects. Heavy interior ribs both add strength to create a solid, non-resonant enclosure as well as break up any possibility of standing waves within the cabinet. Along the rear panel, threaded inserts (M8 Omnimount pattern) allow for various secure wall-mount possibilities, which should be appreciated in 5.1/7.1 installations, particularly for hanging rear surround channels.

In rear-ported designs, LF energy exiting the back of the enclosure can create unpredictable acoustical results. Opal’s front ports use a patent-pending variable impedance approach that combines slotted vents along either side of the drivers with flared airways that substantially reduce air distortion artifacts.

Ready, Set, Opal
The Opals arrived well packed—each is protected by an outer box, two large Styrofoam inserts, a cardboard liner, velvet drawstring bag and two reusable straps for removing the speakers from the shipping materials without putting a thumb through a driver. No grilles are provided—or optional—but a handle on the top of each monitor simplifies moving these beasts around.

Opals self-mute during power-up, so there are no nasty whumps. Beneath a removable cover on the front baffle are knobs for tweaking Opals to personal taste or acoustical considerations. Besides a brightness switch for the illuminated Event logo, controls include level (±6dB input sensitivity), quarter/half/full-space (LF compensation for wall or corner placement) and LF/HF shelving filters. I liked the latter—these are gentle, extremely wide-Q filters offering subtle ±1.5dB tweaks, just enough for a little fine touching.

The semiparametric, cut-only LF filter with a sweepable frequency control (40 to 280 Hz) and two six-position switches for adjusting Q (narrow to wide) and cut depth (0 to -20 dB) was highly useful. This let me selectively notch a problematic room mode with surgical precision, without destroying adjacent frequencies. After this minor tweak, I was ready to go. There was no adjustment period where I felt I had to get “used to” the monitors. These sound great right out of the box.

The HF unit can be rotated for horizontal use.

Event plans to offer an optional software/calibration mic package for
simplifying room/speaker setup, but it wasn’t shipping in time for this
review. Yet thanks to the front controls, I could make tweaks without
moving far from the sweet spot and, once set, the cover hides the knobs
from unauthorized twiddlers. During setup, I detected no port noise
(wheezing or chuffing), which can be a problem with some front-ported
systems, although with nearly 750 watts of amps in each box, up close
you can discern a bit of amplifier hiss when no signal is fed into the

Each speaker includes a thick rubber plinth, a multifunction slab that
keeps the speakers from moving, prevents vibrational transmission to
stands/other surfaces and provides a stable base for the curved
cabinets in horizontal use. Event recommends taking the monitors to a
service center to rotate the HF section, yet it’s a straightforward
process most users could easily handle. On their sides with the
(rotated) tweeters facing inward, Opals’ imaging and response was
consistent with the speakers in a horizontal orientation, which is not
the case with most speakers.

In Session
Tracking drums on a large analog board, the Opals
shined. They had no problem handling extreme dynamic range. The
reproduction of extremely fast transients on snare and cymbals was
impressive, like I was standing in front of the kit, rather than seated
in the control room. Thanks to the 600-watt LF amps and the driver
design, the level and acceleration speed to the woofers is incredible.
Opals seem to have an inexhaustible amount of headroom and there was no
distortion at all. The net effect was like listening to a large
three-way system, with chest thumping bass that was full, yet never out
of control.

Traditionally the Achilles’ heel in most two-way designs, Opals’
excellent midrange definition and detail made a huge difference when
working with vocals, letting me clearly hear nuances in mic/preamp
selections when tracking or making subtle signal processing decisions
in the mix. And piano/flute/violin session playbacks showcased the
invisibility of the crossover point, which was totally seamless. The
balance between lows, mids and upper-end was spot-on—at any level—so
mixing on Opals was an absolute pleasure. Thanks to the low-distortion
performance, there was almost no hearing fatigue, even over long
listening periods. You can mix on these for days on end.

Designed to match that of the woofer, the HF waveguide’s horizontal
splay provides wide, even coverage with smooth response, with no
off-axis smearing and a well-defined left/right soundstage over a
fairly wide listening area.

Working on a video score spotlighted Opal’s LF performance. This
project had drums, bass, synth and various sound effects, including a
bubbling scuba tank that was pitch-shifted down an octave, creating
huge amounts of sub bass that lesser systems may not have reproduced.
This LF capacity was also handy on another video project—a live concert
combining stage mics with distant mics at the center and rear of the
room. Here, phase adjustments were critical, and mixes made on the
Opals translated precisely to larger systems as well as small TV

Setting Standards
With the Opals, Event has created a
world-class system that may become the new standard. Combining absolute
accuracy and large three-way performance from a relatively compact
two-way system, serious studio pros will definitely want to give these
a listen.

For more information, visit

George Petersen is Mix’sexecutive editor and operates a small record label at